Painting An Interior Metal Door? what is the best way to paint the interior side of a...
what is the best way to paint the interior side of a metal door; ?
It is contained by the kitchen which exits into the garage......
what kind of paint should be used ? and does it obligation primered?
What type of bursh,roller excetera would be best to use?? so to
leave the smallest bursh,roller ect. marks .....
paint learned i'd like something that would be washable.
Thanks
Certainly the job will be easier if it's a Flush door, but not impossible if it's "paneled". You don't state what might be the current finish, but to be sure KILZ or Zinser, make an excellent primer product, if you enjoy access.
I paint every day of my enthusiasm, and once prepped, a metal door accepts paint as a wooden door will. I own a commercial building I maintain on a regular justification, with dozens of metal clad fire doors, and I use a fine,Tight cell) foam, roller cover. It will volunteer the smoothest finish, and I just use an interior SATIN Latex paint. Certainly you can use a Semi Gloss, or if the doorway is trimmed, use alike as the trim paint formulation.
If you don't wish to brush cut and camouflage a doorknob of lock plates, remove them first to replace when the paint is dry.
Steven Wolf
just my two "sense"
If there is no rust, a moment ago use a good interior latex paint. If within is rust, sand lightly and paint near a metal primer. If there isn't any rust, and you are shifting the color of the door, you may want to prime it first with a primer resembling Kilz or Zissler. If the door is all you are going to paint, a quart of primer and a quart of paint will be plenty. You will probably own some left for adjectives touch-up.
Clean the area of the door that you are going to paint. Use something similar to Windex, and follow up with plain wet on a cloth.
For best results, take the door stale of it's hinges, and lay it down on something similar to sawhorses, or four 5 gallon plastic buckets under the corners. The hinge pins will pop out from underneath if you stroke a small nail surrounded by the little hole in the bottom of the hinge.
If you want a smooth finish, use roller nap with 1/4" glutinous nap on a full sized roller frame. If the door have a raised nouns, you will need a brush for the areas that the roller will miss. If you want it to be washable, use a semi-gloss or eggshell finish paint. You may run with full make notes on, but it may be harder to roll out smooth. Lay down a drop-cloth, or lots of newspaper lower than the door. If you buy your paint at a home center store like Lowe's or Homer De Poe, the being in the paint dept may know how to give you some pointers on rolling technique. Have fun!
Answers: These doors usually own a factory applied primer, sometimes even a white finish. If that is the armour, you simply need to:
1) Sand delicately with a fine sandpaper to break any surface polish that may have developed.
2) Wipe down next to mineral spirits and a clean, lint free cloth. This will remove any grease from factory processing and handling. Allow to dry completely.
3) Spot prime any bare metal. Use a appropriate (Rustoleum) white metal primer. Dry completely, 24 hours is usually good.
4) Paint near a good aspect interior latex paint. I prefer an acrylic latex semi-gloss. This will allow for easy cleaning. You can drop the explain down to a satin or eggshell, but you loose a bit of durability for each step down.
If the door is flat, a short snooze (1/4") roller will do nicely. If you enjoy a pattern stamped into the door or a skylight, better to use brushes. High quality synthetic brushes will contribute you a good result. 3" or 4" for the broad parts, 1 1/2" angled to get around window and into the recessed areas of an embossed door. Clean your brushes well after you are done and you can use them again for another project.
One ultimate note for rollers and brushes -- bring them damp (not dripping wet) until that time you start painting. Run some marine over them then dry as resourcefully as you can with a towel. This will weaken the tool marks you will see as you paint.
Almost forgot, if by randomness your door is not factory primed, do step 2, prime the entire door for step 3, then verbs to step 4. Again good talent white metal primer.
Bought exotic door & was advise not to have a factory applied finish since it might return with dinged during installation & unsure of final color.
Wisdom from contractor ........
Door was factory primed so adjectives it needed was a wash.
Would prime if bare metal.
Applied Bengamin moore latex eggshell interior paint using a suitable brush for details & a small mohair roller for flat surfaces.
No marks at adjectives , stands up to large dog & cleans up ably.
Best regards