Starting kitchen wall tile? We bought the tile. Our wall has contemporary drywall behind (unpainted...
We bought the tile. Our wall has contemporary drywall behind (unpainted and clean). We are putting the tile from above the backsplash to lower than the wall cabinets. Can you please answer my question:
1) Do you prep the walls with anything? We bought this tub of stuff call Thinset... Is this the actual adhesive or is in attendance something else used to put on afterward?
2) We are doing our longest wall with counter and sink/window afterwards corner and over to counter and stove then counter. Where would the starting point be? Corner or one wall?
3) The wall cabinet on the get underway end is nearly 1/2 inch in consequently the base cabinet right below. If we start the tile from the bottom, when you attain to the top, the tile will hang out from the wall cabinet by the 1/2 surrounded by. Do we use a straight line from the wall cabinet or podium cabinet and it be off any way?
4) The tile is not coated or shiny. Once they are applied to the wall and afterwards grouted and wiped verbs, do you apply any coating?
you have need of spacers...( couple $'s a bag, solitary 1 bag needed..)You requirement to grout the tile after applying to the wall, wait 24 hrs or as the mortor say....I would recommend a grout sealer- they can be brush on or spray on..the grout will collect dust, grease and be a nightmare to clean ... contained by bathrooms you normally put backerboard up to that time tile( it is made of concrete and keeps the wet from penetrating to the drywall...conjure up having to rip out the dryway and re do it....If they are simple sq tiles, no outline involved, then you can start at the edge/ completion...if you want the corners to be 2 perfect sqs meeting- i.e. where you should start- later you won't have a cut piece butting up to an uncut or two cuts dialogue (this is what sounds right for your project)
...you can use the backsplash as a base---to support the tile as it dries. Use painters blue cassette to help hold it to the wall until later....do one row all along the backsplash using the backsplash as support and a small piece of video securing it to the wall until the mortor takes hold..remove the cartridge to start on the next row up and safe and sound with cartridge as before....verbs until done.
Use spacers 1/4" to keep things straight...use a even to get 1st row straight, snap chalk line/ draw column...
PLEASE- double check your thinset to be sure it is recommended for your size tile and for wall use...the premixed stuff has a penchant to shrink up as it dries (and it stays wet for a VERY long time esp contained by high humidity/ moist areas)...cause your tile to come free from the surface it is attatched to... I would get a small daypack of the real, mix it yourself mortor- it is concrete and dries as such... I own used the premixed stuff and had dismal results. Have fun!
This is a long question. First it is not apt to lay tile on drywall your best bet is to get the rock board for tile it is not that expensive. Take out the drywall where on earth the tile is to go and replace it beside hardibacker board.
Just pick a side but it is best to start at the bottom when you lay the tile. Make your corner is square or your tile is going to be off.
I am not sure roughly speaking question 3 but you will hold to cut the tile to fit. Use a level and try to cut to fit as you travel. There is a little room to that you can play next to but try to keep things close. Unless your tile is rough or here are a lot of holes contained by it, there is no requirement to seal the tile. The grout wishes to be sealed. In the kitchen germs will grow in the cracks so put a coat of sealer on.
Take your time and it will work out
Answers: 1 - Thinset is the adhesive. You do not inevitability to prep drywall with anything.
2 - You should standard the entire length of where you are tiling. Then divide that contained by half. That is your starting point. You'll want to lay out the tiles past actually attaching them to label sure you have at smallest 1/2 tile on either expire when you are finished. If you have smaller number than 1/2 tile on either closing stages, move your center point one way or the other. The final centerpoint will be the space between your first two tiles.
3 - Do a straight flash from the cabinet that sticks out more. You'll then have need of to trim the tiles when it narrows but it won't be noticible near only 1/2 inch.
4 - If it's for your wall, you don't requirement any coating. If it was going to be your countertop you'd obligation a clear sealant.
interesting...