Primer coat looks awful. do i do a second primer coat? I am a terrible painter trying my best here... I am repainting...
I am a terrible painter trying my best here... I am repainting some deep green baseboard to a taupe. I am about half channel through with a primer coat and it is all streaky and asymmetrical. why? I cleaned it with tsp first. (it is on the wall.) do i need to do a second primer coat or will my paint probably cover it? The paint is satin enamel Behr Premium plus.
Help!! (some encouragement would also be courteous. I am afraid I am destroying my living room.)
The primer never looks similar to the real paint. The paint will cover it fine.
What primer are you using? If it's one that won't cover the type of paint to be precise existing it will cause streaking. When I repaint I use Zinser 123 - that stuff covers EVERYTHING!! Including my daughters "wall drawing" section. She used crayons, marker and ink pens and it took only one coat to cover it.
Also try using a "good" brush. One that is to say made of natural bristles. Don't load the brush more than 1/2 inch from the tips of the bristles. Do a flimsy coat first, thin. Then do a second coat when it's dry.
Since you are already in the middle of this - stop, consent to what you have done dry and do a test verbs with a second coat and let that dry. See how it looks next. Should be fine. Just remember to keep your layers gossamer. Better to do 2 or 3 thin than one thick.
Good Luck! Run a follower in the room so you can clear out the fumes so you're not light head when you're done!! :>)
Answers: Primer doesn't need to look good. It's individual meant to help the colour coat bond to doesn`t matter what you're painting, and needs to completely cover the dated paint without drips or other uneven texture. Is your primer designed to go over any type of paint? If you don't know what type of paint is on your baseboards, you should be using a primer suitable for going on all types. Try some of your colour on what you've already done, and expect the colour to help yourself to two coats to cover completely. Let dry properly before the second coat. And ditch the foam brush, they're awful and take more time to paint near. Buy a good or better quality brush and look after it. Bristle for grease based paints, synthetic for latex. Bristle tends to hold water from the latex paint, making the brush hold too much paint and be very large to use. An experienced painter could cope with it but that's not you.
When you are painting near a brush, paint towards the new paint, at least on the final ratify of the brush. That's so you don't get brush marks contained by the paint where you start the stroke. Painting toward the new paint let the brush feather in between the paint that's already on and what you're putting on .
Painting is almost adjectives about prepping well and using virtuous materials. You cannot get a good paint duty if what the paint is going on isn't good to begin near. You're using a very good colour coat but a cheap primer. I would enjoy done the reverse if I really needed to save money. If the primer doesn't work like it should, it's a fritter away of time and money to put good paint on top of it.
sometimes the baseboards are painted with oil base paint even though the walls are painted with latex. If that is the suitcase then you will need to get sure the primer and paint you use are oil based as powerfully. If they are not then once your paint dries it will begin to bubble and outer layer off. (you can paint oil over wet bases but not water basis over oil) Is the surface slick? Sometimes if there's a gloss coat, even the primer won't adhere properly. Try sand lightly with a fine grit sandpaper (100-120 grit).
Primer has a tendency to be streaky and not cover economically. You might want to test paint a small section near your final coat (after the primer is dry) to see what the end result will look like. If it's not the finish you want, afterwards after the 1st coat of primer to dry, and lightly sand it with 80 or 100 grit sandpaper, to smooth out the finish, and apply a second coat of primer. You can sand the second coat, too.
You're doing fine, I'm sure--just presume how great your place will look when you're done!